Benutzer:Eorg

Aus FunkFeuer Wiki
Zur Navigation springen Zur Suche springen

Konfiguration meines Knoten

Knoten: hof28

Kurzerklärung

Ich habe den EdgeRouter in Dachgeschoss habe und nur ein CAT5-Kabel in die Wohnung, wo es an einen "Switch" hängt und an diesem mein Server.

Vom Router weg gibt es drei VLANs: 1 (LAN), 2 (PUBLIC), und 10 (MNGT). Der switch verbindet 2 und 10 mit dem Server


Router

Basis: ER-Setup [1]

  {
      "routername": "hof28-router",
      "username": "█████████",
      "portforwardings": "",
      "portsnmp": "on",
      "ip": "193.238.156.39",
      "laninterface": "eth0",
      "landhcp": "on",
      "nodeid": "3008",
      "webinterface": "",
      "managementbr": "on",
      "olsrvlans": "",
      "sshport": "████",
      "portssl": "on",
      "portssh": "on"
  }

Zusätzliche VLANs 2 und 10 auf eth0.

eth0.10 hinzugefügt zu br1

Im OLSRd V1 Feature Wizard unter OLSRd IPv4 -> HNA4 78.41.112.106 255.255.255.255 eingetragen

Neue Statische Route im GUI:

  Route type: interface
  Destination Network 78.41.112.106/32
  Next hop Interface eth0.2
  Descr.: Helium
  Distance <kein Wert>
  Enable True


"Switch"

Eigentlich Wireless-Router TL-WR841N mit OpenWRT

/etc/config/network File:


  config interface 'loopback'
     option ifname 'lo'
     option proto 'static'
     option ipaddr '127.0.0.1'
     option netmask '255.0.0.0'
  
  config globals 'globals'
     option ula_prefix 'fd74:8d6d:678a::/48'
  
  config switch
     option name 'switch0'
     option reset '1'
     option enable_vlan '1 2 10'
  
  config switch_vlan
     option device 'switch0'
     option vlan '1'
     option ports '0 1 3 4'
  
  config switch_vlan
     option device 'switch0'
     option vlan '10'
     option ports '0t 2'
  
  config switch_vlan
     option device 'switch0'
     option vlan '2'
     option ports '0t 2t'
  
  config interface 'MNGT'
     option type 'bridge'
     option proto 'static'
     option ifname 'eth0.10 eth1.10'
     option ipaddr '10.30.8.4'
     option netmask '255.255.255.0'
     option gateway '10.30.8.100'
     option dns '1.0.0.1 1.1.1.1'
  
  config interface 'LAN'
     option type 'bridge'
     option ifname 'eth0 eth1'
     option proto 'none'
  
  config interface 'PUBLAN'
     option type 'bridge'
     option proto 'none'
     option ifname 'eth0.2 eth1.2'


Raspi "Helium"

Ich bin mir nicht sicher ob das wirklich die laufende Konfiguration ist, da ich sehr viel mit ip eingestellt habe und es erst dann in die Configfiles niedergeschrieben habe.

/etc/systemd/network/eth0.network Datei

  [Match]
  Name=eth0
  
  [Network]
  VLAN=eth0.2
  VLAN=eth0.10
  DNS=10.30.8.100

/etc/systemd/network/eth0.10.netdev Datei

  [NetDev]
  Name=eth0.10
  Kind=vlan
  
  [VLAN]
  Id=10

/etc/systemd/network/eth0.10.network Datei

  [Match]
  Name=eth0.10
  
  [Network]
  Address=10.30.8.5/24
  Address=10.30.8.6/24
  
  [Route]
  Gateway=10.30.8.100
  Table=10

/etc/systemd/network/eth0.2.netdev Datei

  [NetDev]
  Name=eth0.2
  Kind=vlan
  
  [VLAN]
  Id=2
  

/etc/systemd/network/eth0.2.network Datei

  [Match]
  Name=eth0.2
  
  [Network]
  Address=79.41.112.106/32